Node: Built sources example, Previous: Sources, Up: Sources



Built sources example

Suppose that foo.c includes bindir.h, which is installation-dependent and not distributed: it needs to be built. Here bindir.h defines the preprocessor macro bindir to the value of the make variable bindir (inherited from configure).

We suggest several implementations below. It's not meant to be an exhaustive listing of all ways to handle built sources, but it will give you a few ideas if you encounter this issue.

First try

This first implementation will illustrate the bootstrap issue mentioned in the previous section (see Sources).

Here is a tentative Makefile.am.

     # This won't work.
     bin_PROGRAMS = foo
     foo_SOURCES = foo.c
     nodist_foo_SOURCES = bindir.h
     CLEANFILES = bindir.h
     bindir.h: Makefile
             echo '#define bindir "$(bindir)"' >$@
     

This setup doesn't work, because Automake doesn't know that foo.c includes bindir.h. Remember, automatic dependency tracking works as a side-effect of compilation, so the dependencies of foo.o will be known only after foo.o has been compiled (see Dependencies). The symptom is as follows.

     % make
     source='foo.c' object='foo.o' libtool=no \
     depfile='.deps/foo.Po' tmpdepfile='.deps/foo.TPo' \
     depmode=gcc /bin/sh ./depcomp \
     gcc -I. -I. -g -O2 -c `test -f 'foo.c' || echo './'`foo.c
     foo.c:2: bindir.h: No such file or directory
     make: *** [foo.o] Error 1
     

Using BUILT_SOURCES

A solution is to require bindir.h to be built before anything else. This is what BUILT_SOURCES is meant for (see Sources).

     bin_PROGRAMS = foo
     foo_SOURCES = foo.c
     BUILT_SOURCES = bindir.h
     CLEANFILES = bindir.h
     bindir.h: Makefile
             echo '#define bindir "$(bindir)"' >$@
     

See how bindir.h get built first:

     % make
     echo '#define bindir "/usr/local/bin"' >bindir.h
     make  all-am
     make[1]: Entering directory `/home/adl/tmp'
     source='foo.c' object='foo.o' libtool=no \
     depfile='.deps/foo.Po' tmpdepfile='.deps/foo.TPo' \
     depmode=gcc /bin/sh ./depcomp \
     gcc -I. -I. -g -O2 -c `test -f 'foo.c' || echo './'`foo.c
     gcc  -g -O2   -o foo  foo.o
     make[1]: Leaving directory `/home/adl/tmp'
     

However, as said earlier, BUILT_SOURCES applies only to the all, check, and install targets. It still fails if you try to run make foo explicitly:

     % make clean
     test -z "bindir.h" || rm -f bindir.h
     test -z "foo" || rm -f foo
     rm -f *.o core *.core
     % : > .deps/foo.Po # Suppress previously recorded dependencies
     % make foo
     source='foo.c' object='foo.o' libtool=no \
     depfile='.deps/foo.Po' tmpdepfile='.deps/foo.TPo' \
     depmode=gcc /bin/sh ./depcomp \
     gcc -I. -I. -g -O2 -c `test -f 'foo.c' || echo './'`foo.c
     foo.c:2: bindir.h: No such file or directory
     make: *** [foo.o] Error 1
     

Recording dependencies manually

Usually people are happy enough with BUILT_SOURCES because they never run targets such as make foo before make all, as in the previous example. However if this matters to you, you can avoid BUILT_SOURCES and record such dependencies explicitly in the Makefile.am.

     bin_PROGRAMS = foo
     foo_SOURCES = foo.c
     foo.$(OBJEXT): bindir.h
     CLEANFILES = bindir.h
     bindir.h: Makefile
             echo '#define bindir "$(bindir)"' >$@
     

You don't have to list all the dependencies of foo.o explicitly, only those which might need to be built. If a dependency already exists, it will not hinder the first compilation and will be recorded by the normal dependency tracking code. (Note that after this first compilation the dependency tracking code will also have recorded the dependency between foo.o and bindir.h; so our explicit dependency is really useful to the first build only.)

Adding explicit dependencies like this can be a bit dangerous if you are not careful enough. This is due to the way Automake tries not to overwrite your rules (it assumes you know better than it). foo.$(OBJEXT): bindir.h supersedes any rule Automake may want to output to build foo.$(OBJEXT). It happens to work in this case because Automake doesn't have to output any foo.$(OBJEXT): target: it relies on a suffix rule instead (i.e., .c.$(OBJEXT):). Always check the generated Makefile.in if you do this.

Build bindir.h from configure

It's possible to define this preprocessor macro from configure, either in config.h (see Defining Directories), or by processing a bindir.h.in file using AC_CONFIG_FILES (see Configuration Actions).

At this point it should be clear that building bindir.h from configure work well for this example. bindir.h will exist before you build any target, hence will not cause any dependency issue.

The Makefile can be shrunk as follows. We do not even have to mention bindir.h.

     bin_PROGRAMS = foo
     foo_SOURCES = foo.c
     

However, it's not always possible to build sources from configure, especially when these sources are generated by a tool that needs to be built first...

Build bindir.c, not bindir.h.

Another attractive idea is to define bindir as a variable or function exported from bindir.o, and build bindir.c instead of bindir.h.

     noinst_PROGRAMS = foo
     foo_SOURCES = foo.c bindir.h
     nodist_foo_SOURCES = bindir.c
     CLEANFILES = bindir.c
     bindir.c: Makefile
             echo 'const char bindir[] = "$(bindir)";' >$ 

bindir.h contains just the variable's declaration and doesn't need to be built, so it won't cause any trouble. bindir.o is always dependent on bindir.c, so bindir.c will get built first.

Which is best?

There is no panacea, of course. Each solution has its merits and drawbacks.

You cannot use BUILT_SOURCES if the ability to run make foo on a clean tree is important to you.

You won't add explicit dependencies if you are leery of overriding an Automake target by mistake.

Building files from ./configure is not always possible, neither is converting .h files into .c files.