[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [openrisc] Re: openrisc-digest V1 #441
Hi
I have added 256MB memory to my PC.now i have 512MB memory,but
nothing changed.:(
Regards.
kevin
----- Original Message -----
From: paul <paulw@m... >
To: openrisc@o...
Date: Thu, 19 Jun 2003 01:27:25 -0700
Subject: [openrisc] Re: openrisc-digest V1 #441
>
>
> Hi
>
> From ISE manual, XCV 600 to XCV 800 require 512M of memory.
> That might be your problem that it takes so long.
>
> openrisc-digest wrote:
>
> > openrisc@o... openrisc-digest V1 #441
> >
> >
>
> >------------------------------------------------------------------
----
> >From: hy kim <boina9456@h... >
> >Date: Wed, 18 Jun 2003 15:35:15 +0900
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >
> >kevin@o... wrote:
> >
> >
> >
> >>hi,all
> >> i have got the source code from the cvs,and changed
> >>the "xsv_fpga_top.prj" in the
> "xess\xsv_fpga\orp_soc\syn\synplify" to let
> >>synplify find the files.but when i synthezised it ,synplify
> told me several
> >>files couldn't be found.then i copy those files from
> ".old".this time
> >>synplify runs well.but complie takes such a long time!i
> waited half an
> >>hour and stop it.my PC is P4 2.4 and 256MB memory.can
> anyone tell me
> >>if this is normal?
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >I guess that sram memory are too much.
> >
> >Please comment a line "'define SDRAM_GENERIC" in
> rtl/mem_if/sram_top.v
> >and retry.
> >
> >Regards.
> >
> >hy kim
> >
> >
> >
> >
> >
>
> >------------------------------------------------------------------
----
> >From: "zhustudio" <zhustudio@i... >
> >Date: Wed, 18 Jun 2003 18:9:11 +0800
> >Subject: [openrisc] about mips of or1200
> >
> >hi,
> >
> >i have found that the mips of or1200 is to low.
> >Assuming the ording instructions, the or1200's mips is 2 times
> slow to
> >the system clock. (WISHBONE bus run 2_divide sys_clk)
> >And with cache, the simulation tell me that it is only 8-10
> times slow
> >to system clock.
> >I have run the test under orp_soc/sw. so i think the buttleneck
> of it is the width of WISHBONE bus.
> >dose anyone try to enchance the performance?
> >
> >Jiahui Zhu
> >
> >Email: zhustudio@i...
> >Date: 2003-06-18
> >
> >
> >
> >
> >
>
> >------------------------------------------------------------------
----
> >From: kevin@o...
> >Date: Wed, 18 Jun 2003 14:24:27 -0100
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >
> >24:30 2003
> >Received: (from majordomo@localhost)
> > by www.opencores.org (8.12.8/8.12.8) id h5IFOUWA031154
> > for openrisc-list; Wed, 18 Jun 2003 14:24:30 -0100
> >X-Authentication-Warning: localhost.localdomain: majordomo set
> sender to owner-openrisc@o... using -f
> >Received: (from oc@localhost)
> > by www.opencores.org (8.12.8/8.12.8) id h5IFORUt031137
> > for openrisc@o... ; Wed, 18 Jun 2003 14:24:27 -0100
> >Date: Wed, 18 Jun 2003 14:24:27 -0100
> >Message-Id: <msg00098.shtml>
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >To: openrisc@o...
> >From: kevin@o...
> >Sender: owner-openrisc@o...
> >Precedence: bulk
> >Reply-To: openrisc@o...
> >
> >hi,
> > i can't find the "'define SDRAM_GENERIC" in any file in
> the
> >dictionary.when i comment the "'define SRAM_GENERIC" ,i get
> several
> >errors.so,what can i do?where can i get a complete ,
> synthesizable
> >source code?
> >
> >----- Original Message -----
> >From: hy kim <boina9456@h... >
> >To: openrisc@o...
> >Date: Wed, 18 Jun 2003 15:35:15 +0900
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >
> >
> >
> >>kevin@o... wrote:
> >>
> >>
> >>
> >>>hi,all
> >>> i have got the source code from the cvs,and changed
> >>>the "xsv_fpga_top.prj" in the
> >>>
> >>>
> >>"xess\xsv_fpga\orp_soc\syn\synplify" to let
> >>
> >>
> >>>synplify find the files.but when i synthezised it
> ,synplify
> >>>
> >>>
> >>told me several
> >>
> >>
> >>>files couldn't be found.then i copy those files from
> >>>
> >>>
> >>".old".this time
> >>
> >>
> >>>synplify runs well.but complie takes such a long time!i
> waited
> >>>
> >>>
> >>half an
> >>
> >>
> >>>hour and stop it.my PC is P4 2.4 and 256MB memory.can
> anyone
> >>>
> >>>
> >>tell me
> >>
> >>
> >>>if this is normal?
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>I guess that sram memory are too much.
> >>
> >>Please comment a line "'define SDRAM_GENERIC" in
> >>rtl/mem_if/sram_top.v
> >>and retry.
> >>
> >>Regards.
> >>
> >>hy kim
> >>
> >>
> >>
> >
> >
>
> >------------------------------------------------------------------
----
> >From: kevin@o...
> >Date: Wed, 18 Jun 2003 14:25:17 -0100
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >
> >25:18 2003
> >Received: (from majordomo@localhost)
> > by www.opencores.org (8.12.8/8.12.8) id h5IFPI85031248
> > for openrisc-list; Wed, 18 Jun 2003 14:25:18 -0100
> >X-Authentication-Warning: localhost.localdomain: majordomo set
> sender to owner-openrisc@o... using -f
> >Received: (from oc@localhost)
> > by www.opencores.org (8.12.8/8.12.8) id h5IFPH0b031236
> > for openrisc@o... ; Wed, 18 Jun 2003 14:25:17 -0100
> >Date: Wed, 18 Jun 2003 14:25:17 -0100
> >Message-Id: <msg00099.shtml>
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >To: openrisc@o...
> >From: kevin@o...
> >Sender: owner-openrisc@o...
> >Precedence: bulk
> >Reply-To: openrisc@o...
> >
> >----- Original Message -----
> >From: hy kim <boina9456@h... >
> >To: openrisc@o...
> >Date: Wed, 18 Jun 2003 15:35:15 +0900
> >Subject: Re: [openrisc] How can i synthesize or1200?
> >
> >
> >
> >>kevin@o... wrote:
> >>
> >>
> >>
> >>>hi,all
> >>> i have got the source code from the cvs,and changed
> >>>the "xsv_fpga_top.prj" in the
> >>>
> >>>
> >>"xess\xsv_fpga\orp_soc\syn\synplify" to let
> >>
> >>
> >>>synplify find the files.but when i synthezised it
> ,synplify
> >>>
> >>>
> >>told me several
> >>
> >>
> >>>files couldn't be found.then i copy those files from
> >>>
> >>>
> >>".old".this time
> >>
> >>
> >>>synplify runs well.but complie takes such a long time!i
> waited
> >>>
> >>>
> >>half an
> >>
> >>
> >>>hour and stop it.my PC is P4 2.4 and 256MB memory.can
> anyone
> >>>
> >>>
> >>tell me
> >>
> >>
> >>>if this is normal?
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>I guess that sram memory are too much.
> >>
> >>Please comment a line "'define SDRAM_GENERIC" in
> >>rtl/mem_if/sram_top.v
> >>and retry.
> >>
> >>Regards.
> >>
> >>hy kim
> >>
> >>
> >>
> >
> >
>
> >------------------------------------------------------------------
----
> >From: "Damjan Lampret" <lampret@o... >
> >Date: Wed, 18 Jun 2003 17:09:50 -0700
> >Subject: Re: [openrisc] is there a way to rebuild or1ksim from
> verilog source
> >
> >No. You need to add your instruction in or1ksim manually.
> >
> >regards,
> >Damjan
> >
> >----- Original Message -----
> >From: "paul" <paulw@m... >
> >To: <openrisc@o... >
> >Sent: Wednesday, June 18, 2003 2:52 AM
> >Subject: [openrisc] is there a way to rebuild or1ksim from
> verilog source
> >
> >
> >
> >
> >>Hi
> >>
> >>Is there a way to rebuild or1ksim from "or1200" *.v verilog
> source?
> >>That is, can I add an instruction to or1200, and then
> rebuild the
> >>or1ksim, to test the new instruction?
> >>
> >>If not, is there another way to test modification to
> or1200?
> >>
> >>Thanks.
> >>
> >>
> >>--
> >>To unsubscribe from openrisc mailing list please visit
> >>
> >>
> >http://www.opencores.org/mailinglists.shtml
> >
> >
> >
> >
> >
>
> >------------------------------------------------------------------
----
> >End of openrisc-digest V1 #441
> >-
> >To unsubscribe from openrisc-digest mailing list please visit
> http://www.opencores.org/mailinglists.shtml
> >
> >
>
--
To unsubscribe from openrisc mailing list please visit http://www.opencores.org/mailinglists.shtml